Booklet for VX-2 - VX-2 Owner's Manual
This article was helpful for 13 people. Is this article helpful for you?
Why this article is not helpful?
It's missing pages 4-11 through 4-13! Is there anyone I can ask specific questions to diagnose this VX-2 scooter that I have in my shop?
The Electric Bike Shop
1925 F Street
Sacramento, CA 95811
Sure - please post your question her or send me by email: email@example.com
Chase Daniels 5 minutes ago
I have a 2007 Vectrix Maxi Electric, when I turn the key the bike boots up as it supposes to but after lifting the kickstand up and switching the on switch to ON located on the right-hand side when applying the left brake and tapn the right break nothing happens. The ready signal cuts on and everything on the dash including the lights pop on but there is a the word "buSult" that pops up on the left side screen directly beneath where the initials KM/killometer is located. What does that word "buSult" mean, and is there anything I can do to get it to start up.
I have some questions about the EVPS BC:
EVPS BC with the error message "no Out", what is the reason for this error?
Can we repair this error when we change the EVPS charger control board?
No out is a hardware failure on the main board not on the controll board.
If you have some electric expirience (replacing SMD components) - write to Matteo directly on firstname.lastname@example.org - he may advise which components try to replace. Sometimes is the main transformer though - then is not worth to repair.
I have purches a Vextrix Electric Scooter VX-1 , I got the Battery Charge up and it work great. Well I had issue that I took it to a job and the owner had issue with battery that cause spark near the battery. Well After that the scooter will not boot up. I replace the battery, and still will not come on. I thinking it may of motor controller fuse is bad, can you help me out to get it started again.
What do you mean by:
- "owner had issue with battery that cause spark"
- "I replaced the battery" - which battery you put in instead?
I had my scooter stolen but found it later and it seems like they tried to start it by short-circuiting it. I smoldered back black wire from the ignition and the scooter gets electricity again but I can't get the engine going by pressing both handbrakes and when applying the front brake it looks like the scooter is accelerating on the spedometer and the disply shifts the setting between km/miles. I can't find anything else done with the scooter. Do you have any ideas what it could be?
They have damaged the "kill switch" - red button on the right side of handlebar.
Bike is in the OFF status.
You can try to repair it or buy new one in our online store.
I get cannot extract font "EIJXXQ+Ariel-BoldMT". Can you create a new PDF with also all pages? Thanks!!
I bought a vectrix vx-2 without a key ,can you please send me instructions how to change the ignition switch and where to buy one .Thanks Tim 8188522345
my vx2 wont start I did the left right break and it s on but eont go
Please follow instruction. In pt. 7 if you are using PGN value has to be set as 0
I have Vetrix Electric Scooter....for some reason cannot get storage trunk area to open....I placed key in right position, but nothing pops out or loosens up. Suggestions??
Is It VX2 or VX1? is there any tension on key when you are turning it? Anyway, you will need to dissasemble plastic panels of the scooter.
Plastic panel removal
Trunk Latch checkout
I have a VX2. Everything works except that the "handshake" function is unpredictable. Brake lights always illuminate when I pull either brake lever. When I pul both sometimes the lights flash right away (like they should) and other times it may take several minutes of trying before they flash. The issue does not seem to be affected by temperature. Once the lights flash then everything works like it should.
When I plug my Vetrix in to charge it, absolutely nothing happens...no lights appear on dash as charging or anywhere else...ideas??
Customer support service by UserEcho